Article Sidebar

Published: 2026-11-16
Keywords:
coffee pulper , cylinder type , field performance , cherry ripeness , working capacity
Section: Articles
Wanda Citra Lestari  Agricultural Engineering, Hasanuddin University, Makassar , Indonesia
Iqbal Salim  Agricultural Engineering, Hasanuddin University, Makassar , Indonesia
Abstract:

This study describes the field performance of a commercial cylinder-type coffee pulper processing Arabica cherries of two ripeness levels and compares it with the manufacturer’s specification. Cherries were sorted by color into a 90–100% ripe lot and a 40–80% ripe lot and pulped in the field, and the output was separated into whole beans, broken beans, unpulped beans, and skin fragments. Working capacity was 403.51 kg/h for the ripe lot and 228.89 kg/h for the underripe lot against a specified 528.36 kg/h, and whole beans were 95.99% and 82.62% against a specified 95.04%. Unpulped beans rose from 0.58% to 8.25% and broken beans from 0.62% to 2.61%, while skin fragments in the bean stream reached 5.7% and 23.49% against a specified 1.97%. Lower cherry ripeness therefore reduced capacity and bean integrity mainly through unpulped beans rather than breakage, but each lot was tested in three repetitions and only one value per indicator is reported, without dispersion, so the differences are descriptive.

Adesokan, M. A., Yusuff, T. I., Adeleke, S. A., Jimeshio, J. G., & Mofolasayo, A. S. (2025). Performance evaluation of manual single-disc coffee pulper. Iconic Research and Engineering Journals, 9(6).

Akbar, F. B., Yusuf, A., Thoriq, A., & Sugandi, W. K. (2020). Analisis teknik dan uji kinerja mesin pengolah kopi (pulper dan huller) mobile pada Alat Mekanis Multiguna Pedesaan (AMMDes) pengolahan kopi [Technical analysis and performance test of a mobile coffee pulper and huller]. Agroteknika, 3(1), 42–55. DOI: https://doi.org/10.32530/agroteknika.v3i1.65

Ansari, H., Reta, R., Zaimar, Z., Nurmiah, S., Nur, N., Syamsia, S., & Mustafa, A. (2025). Quality characterization of Arabica coffee soaked at different fruit maturity levels. BIO Web of Conferences, 189, 02003. https://doi.org/10.1051/bioconf/202518902003 DOI: https://doi.org/10.1051/bioconf/202518902003

Baroroh, K., Sutopo, Lidyasari, A. T., Eliasa, E. I., & Irsad, K. (2023). The design of pulper machine to increase coffee production capacity in realizing people's economy. Dinamika Vokasional Teknik Mesin, 8(1), 49–61. https://doi.org/10.21831/dinamika.v8i1.54508

Bizimungu, G., Ahouansou, R. H., & Semassou, G. C. (2023). Physical and mechanical properties of Arabica coffee (Coffea arabica L.) cherries and beans in Rwanda. Food Research, 7(5), 283–296. https://doi.org/10.26656/fr.2017.7(5).498 DOI: https://doi.org/10.26656/fr.2017.7(5).498

Bizimungu, G., Ahouansou, R. H., & Semassou, G. C. (2024). Design, fabrication and evaluation of small-scale disc and drum pulpers for Arabica (Coffea arabica L.) and Robusta (Coffea canephora L.) coffee. Journal of the Saudi Society of Agricultural Sciences, 23(6), 404–414. https://doi.org/10.1016/j.jssas.2024.04.001 DOI: https://doi.org/10.1016/j.jssas.2024.04.001

Duque-Dussán, E., Rincón-Jimenez, A., Tinoco, H. A., Cardona, C. I., Ibarra, C. A., & Rodríguez-Sotelo, J. L. (2025). Determination of elastic properties of Coffea arabica L. var. Castillo bean-mesocarp using finite element analysis and experimental methods. Journal of Food Process Engineering, 48(12), e70303. https://doi.org/10.1111/jfpe.70303 DOI: https://doi.org/10.1111/jfpe.70303

Gutiérrez Madrid, F., Fabio Quintero, H., & Díaz, A. (2026). Experimental characterization and finite element modeling of mechanical compression in Coffea arabica fruits from different varieties. International Journal of Food Properties, 29(1), Article 2731038. DOI: https://doi.org/10.1080/10942912.2026.2731038

Hendrawan, A. B., & Ariyanto, N. A. (2021). Analisis jarak celah pengupas dengan variasi putaran poros pengupas pada mesin pengupas kopi basah (pulper) [Analysis of peeler clearance with varied peeler shaft speed in a wet coffee pulper]. Nozzle: Journal Mechanical Engineering, 10(2), 62–65. DOI: https://doi.org/10.30591/nozzle.v10i2.2821

Iqbal, Ferialdi, Paliling, A. R., Azis, A., Mursalim, Achmad, M., Waris, A., Hardinasinta, G., Mubarak, H., Hati, F. I. P., & Rizal, M. (2024). Development of power supply system solar base for coffee pulper. Acta Technologica Agriculturae, 27(4), 219–226. https://doi.org/10.2478/ata-2024-0029 DOI: https://doi.org/10.2478/ata-2024-0029

Philippine Agricultural Engineering Standard (PAES). (2011). PAES 253:2011 Agricultural machinery – Coffee pulper – Methods of test. Agricultural Machinery Testing and Evaluation Center, University of the Philippines Los Baños.

Rinaldi, M., Iqbal, Azis, A., & Mursalim. (2024). Rancang model sistem mobile untuk mesin pengupas kopi (pulper) [Design of a mobile system for a coffee pulper]. Jurnal Ilmiah Rekayasa Pertanian dan Biosistem, 12(1), 14–25. https://doi.org/10.29303/jrpb.v12i1.537 DOI: https://doi.org/10.29303/jrpb.v12i1.537

Sidi, J. P., Pramono, C., & Widodo, S. (2018). Analisis mesin pengupas biji kopi basah jenis Arabica dengan variasi putaran pengupas [Analysis of a wet Arabica coffee pulper with varied peeler speed]. Jurnal MER-C, 1(2).

Sutopo, & Irsad, K. (2025). The design of a coffee pulper machine by using Inventor Autocad software. Journal of Applied Mechanical Engineering Innovation, 1(1), 33–41. https://doi.org/10.21831/jamei.v1i1.880 DOI: https://doi.org/10.21831/jamei.v1i1.880

Tinoco, H. A., Buitrago-Osorio, J., Perdomo-Hurtado, L., Lopez-Guzman, J., Ibarra, C. A., Rincon-Jimenez, A., Ocampo, O., & Berrio, L. V. (2022). Experimental assessment of the elastic properties of exocarp–mesocarp and beans of Coffea arabica L. var. Castillo using indentation tests. Agriculture, 12(4), 502. https://doi.org/10.3390/agriculture12040502 DOI: https://doi.org/10.3390/agriculture12040502

Velásquez, S., Peña, N., Bohórquez, J. C., Gutierrez, N., & Sacks, G. L. (2019). Volatile and sensory characterization of roast coffees – Effects of cherry maturity. Food Chemistry, 274, 137–145. https://doi.org/10.1016/j.foodchem.2018.08.127 DOI: https://doi.org/10.1016/j.foodchem.2018.08.127

Widyotomo, S., Ahmad, H., Soekarno, S. T., & Mulato, S. (2011). Performance of a horizontal triple cylinder type pulping machine. Pelita Perkebunan, 27(1). https://doi.org/10.22302/iccri.jur.pelitaperkebunan.v27i1.144 DOI: https://doi.org/10.22302/iccri.jur.pelitaperkebunan.v27i1.144

Yuliani, N. M. T., Setiyo, Y., & Widia, I. W. (2025). Pengaruh lama penyimpanan buah kopi arabika (Coffea arabica L.) petik merah terhadap kinerja mesin pulper pengupas kulit daging buah secara basah [Effect of storage duration of red-picked Arabica cherries on the performance of a wet pulper]. Jurnal BETA (Biosistem dan Teknik Pertanian), 13(2), 241–249.Wan

Wanda Citra Lestari wancilesttt@gmail.com

Agricultural Engineering, Hasanuddin University, Makassar

Indonesia

Iqbal Salim

Agricultural Engineering, Hasanuddin University, Makassar

Indonesia

Field Performance of a Cylinder-Type Coffee Pulper at Two Cherry Ripeness Levels. (2026). Salaga Journal, 4(2), 63-69. https://doi.org/10.70124/salaga.v4i2.2338
Data statistik bulanan belum tersedia.